Power Generation and Distribution

Our Rating for the course : 4.7 Stars Based on 56 users

Introductions

Electric power distribution is the final stage in the delivery of electric power; it carries electricity from the transmission system to individual consumers. Distribution substations connect to the transmission system and lower the transmission voltage to medium voltage ranging between 2 kV and 35 kV with the use of transformers. Primary distribution lines carry this medium voltage power to distribution transformers located near the customer's premises. Distribution transformers again lower the voltage to the utilization voltage used by lighting, industrial equipment or household appliances. Often several customers are supplied from one transformer through secondary distribution lines. Commercial and residential customers are connected to the secondary distribution lines through service drops. Customers demanding a much larger amount of power may be connected directly to the primary distribution level or the subtransmission level.

Nbiz Infosol provides this course in UAE specifically in Abu Dhabi, Dubai, Ajman, RAK, Al Ain, Umm Al Quwain and other areas

Course Objectives

Duration & Learning Level

Learning Level: Intermediate

Duration: 3day(s)

<<Back to schedule
Training Provider	Nbiz Infosol	Course Name
Candidate Name *		Company Name
Student Type		Student Type ID
Student ID Number		Mobile # *
Email*		Registration Ref

Name of Course	Scheduled Dates	Venue	Registration Link
Power Generation and Distribution	To be determined	Abu Dhabi, UAE	Register Now »»

Nbiz delivers this course in Abu Dhabi, Dubai, RAK, Ajman, Sharjah, Kuwait, Oman, Saudi, Bahrain , egypt and other places in the UAE and in the Middle East

The gas-turbine cycle / Conversion of heat to mechanical energy
Typical values of temperature and pressure "through cycle" / Single shaft and two shaft arrangements
Exhaust heat recovery / Axial flow and centrifugal flow compressors
Effect of pressure ratio on efficiency / Potential for compressor stall at start-up / Variable inlet guide vanes
Combustor arrangements / Combustion air, and secondary air / Factors affecting air temperature rise through the combustion section
Combustion igniters, and flame detectors / Water and steam injection
Distribution of turbine energy; to compressor, generator, auxiliaries, and stack. Vs. Gas turbine efficiency
Gas-turbine starting arrangements
Single Line Diagram & Distribution Layout
Types of Distribution Substation

Power Generation and Distribution

Upon completion of this course participants will be able to know:  GE Gas turbine cycle in details.  Generator Construction, Operation & Troubleshooting.  Power Transformers Construction, Operation & Troubleshooting. Power Distribution System.  The gas-turbine cycle  Conversion of heat to mechanical energy  Typical values of temperature and pressure "through cycle"  Single shaft and two shaft arrangements  Exhaust heat recovery  Axial flow and centrifugal flow compressors  Effect of pressure ratio on efficiency  Potential for compressor stall at start-up  Variable inlet guide vanes  Combustor arrangements  Combustion air, and secondary air  Factors affecting air temperature rise through the combustion section  Combustion igniters, and flame detectors  Water and steam injection  Distribution of turbine energy; to compressor, generator, auxiliaries, and stack. Vs. Gas turbine efficiency  Gas-turbine starting arrangements  Accessory gear box drive to auxiliaries  Control of gas turbine output  Generator Construction - Excitation Systems, voltage & frequency Control  Generator auxiliary systems - Normal & Abnormal operations  Generator maintenance activities  Stator and rotor visual inspection - Generator electrical tests  Single Line Diagram & Distribution Layout  Power & Auxiliary Transformers  Distribution Substation Construction  Distributed power and local networks  Types of Distribution Substation

Completion Certificate will be awarded after training

1. How do I enroll/register for the training course?

To enroll or register to any training course, you can use the registration page from training page or fill the request a call back form from each course pages. The following page will provide you a list of course and training that we are providing based on the category and from each course item you can see the course details.
URL: http://www.nbizinfosol.com/training.aspx
Another method is to fill a Request a call back form provided in each Training/Course pages.

2. What will I get along with this training?

We are providing course materials during training and completion certificate after succesful training.

3. Do I need to fill up a registration form?

Yes. you can fill the registration form avaialble in the website or you can directly call us to enroll the course.Our executives will guide you to do further steps.

4. Does the course fees include the examination fee as well?

Based upon the course you are enrolling, we will charge the exam fee . We will give you the details of course fee and exam fee anytime to clear it.

5. Do you provide any course completion certificate?

Yes. We are providing the Course completion certificate for all courses we are providing.

6. Do you provide assistance for the exam appliation process?

Yes. We will provide assistance and support to apply for any exam.

7. What is the mode of payment?

Two types of payment available:

1. Visit our office and pay direct,You are always welcome to Nbizinfosol.
2. We are providing online payment via paypal payment gateway.Based upon your request we will provide the link to access the payment page.

Operation Engineers, Power Plant Operators & foremen

Note: The listed information (venue, schedule, duration and content) may be modified and customized as per the requirements.

Infra Structure Security

Information Security Soultions

Power Generation and Distribution

Introductions